manualshive.com logo in svg

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 35 / 183

Поделиться
Скачать
Gilera Runner RST 50 SP Скачать руководство пользователя страница 35

Top-up

Proceed as follows:

1.

 rest the vehicle on its centre stand with the han-

dlebars perfectly horizontal;

2.

 remove the rear-view mirrors;

3.

 remove the front handlebar cover;

4.

 remove the tank cover «

A

» loosening the two

fixing screws «

B

» and restore the level using only

the prescribed fluid without exceeding the maxi-

mum level.

Under normal climatic conditions, the liquid should

be replaced every two years. This operation must

be carried out by trained technicians, please con-

tact an 

Authorised Piaggio-Gilera Service Cen-

tre

CAUTION

TOP UPS SHOULD ONLY BE CARRIED OUT WITH DOT 4
CLASSIFIED BRAKE FLUID.

CAUTION

THE BRAKING CIRCUIT FLUID IS HIGHLY CORROSIVE.
THEREFORE, WHEN TOPPING IT UP, AVOID LETTING IT
COME INTO CONTACT WITH THE PAINTED PARTS OF
THE VEHICLE. THE BRAKING CIRCUIT FLUID IS HYGRO-
SCOPIC, THAT IS, IT ABSORBS HUMIDITY FROM THE
SURROUNDING AIR. IF MOISTURE CONTAINED IN THE
BRAKE FLUID EXCEEDS A CERTAIN VALUE, THIS WILL
RESULT IN INEFFICIENT BRAKING.

WARNING

IN NORMAL CLIMATIC CONDITIONS IT IS ADVISABLE TO
REPLACE THE ABOVE-MENTIONED FLUID EVERY 2
YEAR. NEVER USE BRAKE FLUID CONTAINED IN CON-
TAINERS WHICH ARE ALREADY OPEN OR PARTIALLY
USED.

Recommended products

AGIP BRAKE 4

 

Brake fluid

FMVSS DOT 4 Synthetic fluid

Runner RST 50 SP

Maintenance

MAIN - 35

Содержание Runner RST 50 SP
























































































































































































Отзывы:

Нет отзывов