Gilera Runner RST 50 SP Скачать руководство пользователя страница 128

Страница: 128 / 183

Knee-guard

- Remove the central chassis cover.

- Remove the shield central cover and remove the

supporting screws for the expansion tank.

- Remove the 10 screws (5 per side) of the shield

back plate indicated in the photograph.

- Remove the central screw <

> indicated in the

photo, then remove the shield back plate.

Follow the procedure in reverse order to refit.

See also

Frame central cover
Front central cover

Removing the ignition key-switch when on *off*

- Remove the front shield and back shield.

- Insert a small awl in the groove shown in the

photo and pry up until the clamp is removed.

- Remove the lock body.

To fit, repeat the procedure in the reverse direc-

tion.

See also

Legshield
Knee-guard

Removing the ignition key-switch when on *lock*

Remove the shield.

- Remove the switch of the key switch.

- Make a hole on the block using a drill as shown

in the figure.

- Insert the wheel cylinder with the key and with the

anchoring tab facing down halfway on the lock

body taking care that the insertion phase of the key

is oriented matching "ON" (the only position that

enables the cylinder to get into the lock body); now

Chassis

Runner RST 50 SP

CHAS - 128

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 128 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: