Gilera Runner RST 50 SP Скачать руководство пользователя страница 89

Страница: 89 / 183

Choosing the gasket

• Temporarily fit the cylinder on the piston, without

the basic gasket.

• Fit a dial gauge on the specific tool, using the

short union as shown in the figure.

Use a reference plane to reset the dial gauge with

a pre-load of a few millimetres.

Set the dial gauge.

Check that tracer slides smoothly.

Fit the tool on the cylinder without changing the

dial gauge position.

Lock the tool by the nuts used to secure the head.

Turn the engine shaft to the dead centre position (dial gauge rotation inversion point).

Measure the difference with the reset value.

Refer to the table to identify the thickness of the cylinder base gasket to use for refitting. The correct

identification of the thickness of the cylinder base gasket allows maintaining the correct compression

ratio.

Remove the specific tool and the cylinder.

Specific tooling

020272Y

Piston position check tool

See also

Cylinder - piston assy.

Runner RST 50 SP

Engine

ENG - 89

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 89 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: