Gilera Runner RST 50 SP Скачать руководство пользователя страница 121

Страница: 121 / 183

Using the air heater, warm up the water pump

bearing housing, without directing the air flow di-

rectly against the oil seal

- Lubricate the end of the water pump shaft on the

oil seal side, using the recommended product.

Recommended products

AGIP GREASE MU3

Grease for odometer

transmission gear case

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

- Insert the shaft, with bearings, into its housing by

pushing and turning it at the same (turn anticlock-

wise for tightening)

- Turn it rapidly to the end of the threading.

- Should this operation prove difficult, do not carry

on; instead, start over by reheating the crankcase

N.B.

FAILURE TO OBSERVE THIS RULE MAY RESULT IN DAM-
AGE TO THE THREAD OF THE COPPER INSERT ON THE
IMPELLER, OR SEPARATION OF THIS FROM THE IMPEL-
LER ITSELF.

Specific tooling

020169Y

Water pump crankshaft fitting and re-

moval spanner

See also

Removal

Thermostat

Removal

•

Detach the coolant hose from the

head, partially draining the system.

•

Remove the cylinder head.

•

Remove the two fixing screws and

hence the thermostat.

Runner RST 50 SP

Cooling system

COOL SYS - 121

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 121 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: