Gilera Runner RST 50 SP Скачать руководство пользователя страница 41

Страница: 41 / 183

Possible Cause

Operation

no air in the circuits; if necessary, bleed the air. Check that the

front brake calliper moves in axis with the disc.

Fluid leakage in hydraulic braking system

Failing elastic fittings, plunger or brake pump seals, replace

Brakes overheating

OVERHEATING BRAKES

Possible Cause

Operation

Brake disc slack or distorted

Check the brake disc screws are locked; use a dial gauge and

a wheel mounted on the vehicle to measure the axial shift of

the disc.

Defective piston sliding

Check calliper and replace any damaged part.

Electrical system

Battery

BATTERY

Possible Cause

Operation

Battery

The battery is the electrical device in the system that requires

the most frequent inspections and thorough maintenance. If the
vehicle is not used for some time (1 month or more) the battery

needs to be recharged periodically. The battery runs down

completely in the course of 5 ÷ 6 months. If the battery is fitted
on a motorcycle, be careful not to invert the connections, keep-

ing in mind that the black ground wire is connected to the

negative terminal while the red wire is connected to the terminal
. Follow the instructions in the ELECTRICAL SYSTEM

chapter for the recharging of the batteries.

Steering and suspensions

Rear wheel

POOR ROAD HOLDING

Possible Cause

Operation

Faulty suspension

Check that the rear shock absorber and/or the front fork is/are
in good working order. Replace or overhaul the front fork and/

or replace the rear shock absorbers in case of malfunction

Tyres deflated or damaged

Check the correct pressure of the tyres and the condition of the

tread. Inflate to the correct pressure or replace.

Loosen the anchorage points of the front and/or rear suspen-

sion unit.

Check the tightness between the frame, swinging arm and en-

gine and the fixing of the wheels to the hub and/or the axle.

Check the correct tightening of the steering ring nut.

Heavy steering

STEERING HARDENING

Possible Cause

Operation

Torque not conforming

Check the tightening of the top and bottom ring

nuts.

Runner RST 50 SP

Troubleshooting

TROUBL - 41

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 41 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: