Gilera Runner RST 50 SP Скачать руководство пользователя страница 118

Страница: 118 / 183

System bleed

1. Fill the circuit through the expansion tank to

the maximum level.

2. Fasten the rubber line to the drain fitting on

the head and thread it into the expansion

tank mouth..

3. Loosen the fitting and restore the tank level.

4. Start up the engine and wait until only cool-

ant exits from the line, then tighten the fitting

on the head..

5. Turn off the engine, restore the level of liquid

to the maximum level, then close the expan-

sion tank..

6. Heat up the engine to normal operating tem-

perature in order to eliminate any air forma-

tion in the main lines..

7. Stop the engine and let it cool, then check

that the level of coolant in the expansion tank

to the maximum;; refill it.

Water pump - overhaul

- Remove the rpm sensor /coolant delivery hose

clamp

- Remove the transmission cover

- Remove the mixer

- Position the tool as shown in the picture

N.B.

WHEN SECURING THE TOOL, PAY ATTENTION NOT TO
OVERLOAD THE PLASTIC IMPELLER.

Specific tooling

020620Y

Water pump impeller stop

Cooling system

Runner RST 50 SP

COOL SYS - 118

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 118 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: