Gilera Runner RST 50 SP Скачать руководство пользователя страница 134

Страница: 134 / 183

Radiator fan

- Set up a receptacle to collect coolant.

- Remove the fuel tank.

- Loosen the clamps and disconnect the 4 lines

from the radiator.

- Remove the radiator by the 4 studs shown in the

figure.

See also

Fuel tank

Frame central cover

Expansion tank

- Remove the front shield.

Remove the screw indicated in the photograph.

- Remove the cap momentarily to disconnect it

from the shield back plate by pulling it downwards.

- Disconnect the expansion tank from the support

anchored to the chassis.

- Prepare a container to collect the coolant.

- Remove the coolant in (top) and return (bottom)

pipes.

Assembly following the procedure in reverse or-

der.

See also

Legshield

Mixture oil tank

- Remove the helmet compartment.

- Disconnect the connector of the oil gauge light and the oil pipe and remove the tank

Chassis

Runner RST 50 SP

CHAS - 134

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 134 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: