manualshive.com logo in svg

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 2 / 183

Поделиться
Скачать
Gilera Runner RST 50 SP Скачать руководство пользователя страница 2

SERVICE STATION

MANUAL

Runner RST 50 SP

The descriptions and illustrations given in this publication are not binding. While the basic specifications
as described and illustrated in this manual remain unchanged, PIAGGIO-GILERA reserves the right, at

any time and without being required to update this publication beforehand, to make any changes to

components, parts or accessories, which it considers necessary to improve the product or which are

required for manufacturing or construction reasons.

Not all versions/models shown in this publication are available in all countries. The availability of single

versions should be checked at the official Piaggio sales network.

"© Copyright 2007 - PIAGGIO & C. S.p.A. Pontedera. All rights reserved. Reproduction of this publication

in whole or in part is prohibited."

PIAGGIO & C. S.p.A. - After-Sales

V.le Rinaldo Piaggio, 23 - 56025 PONTEDERA (Pi)

Содержание Runner RST 50 SP
























































































































































































Отзывы:

Нет отзывов