Gilera Runner RST 50 SP Скачать руководство пользователя страница 122

Страница: 122 / 183

Check

1) Visually check that the thermostat is not dam-

aged.

2) Fill a metallic container with approx. 1 litre of

water.

Immerge the thermostat, and keep it in the centre

of the bowl.

Immerge the multimeter temperature probe, and

keep it close to the thermostat.

Heat up the bowl using the thermal gun.

Check the thermostat opening start temperature:

Heat up until the thermostat is completely open.

3) Replace the thermostat if not working properly.

CAUTION

TO EXECUTE THE TEST CORRECTLY, MAKE SURE NEI-
THER THE THERMOSTAT NOR THE THERMOMETER
TOUCHES THE CONTAINER.

Specific tooling

020331Y

Digital multimeter

020151Y

Air heater

Characteristic

Thermostat check: Opening start temperature

60±2°C

Refitting

•

Refit the thermostat onto the head, fol-

lowing the removal operations in the

reverse order, and paying attention in

inserting the groove on the thermostat

on the reference on the head.

Cooling system

Runner RST 50 SP

COOL SYS - 122

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 122 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: