manualshive.com logo in svg

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 55 / 183

Поделиться
Скачать
Gilera Runner RST 50 SP Скачать руководство пользователя страница 55

BREAKDOWN 4

Put the vehicle in gear and place the alternating

voltage tester between the insertion of the blue-red

cable and the yellow cable on the stator to check

that the voltage distributed by the generator is be-

tween the values indicated. In the event of abnor-

malities, check the continuity of the stator, or

continue with testing.

Insert the ammeter between the stator (blue-red

cable) and the battery and using the tester to

check that the current distributed at 3000 rpm is

between 12V and 13V as indicated. If the values

are lower than necessary, replace the regulator or

the battery.

N.B.

BEFORE CARRYING OUT THE CHECKS ON THE REGU-
LATOR AND RELATIVE SYSTEM, IT IS ALWAYS GOOD
PRACTICE TO CHECK THAT THERE IS CONTINUITY BE-
TWEEN THE BLACK CABLE AND THE GROUND.

N.B.

TO KEEP THE BATTERY BETWEEN 12 AND 13V, CAUSING
CURRENT ABSORPTION BY THE SYSTEM, A 12V - 35W
BULB CONNECTED BETWEEN THE + BATTERY AND
GROUND CAN BE USED.

Specific tooling

020331Y

 

Digital multimeter

Characteristic

Distributed current

1.5 to 2A

Voltage distributed at 3000 rpms

25 to 30V

FAULT 5

If the turn indicators do not work, do the following:

•

Without removing the connector from

the voltage regulator, move the key-

controlled switch to ON and verify the

presence of intermittent voltage be-

tween contact 7 and the ground. If

there is voltage, the failure must be at-

tributed to the flashing indicator switch

Runner RST 50 SP

Electrical system

ELE SYS - 55

Содержание Runner RST 50 SP
























































































































































































Отзывы:

Нет отзывов