Gilera Runner RST 50 SP Скачать руководство пользователя страница 79

Страница: 79 / 183

Refitting the driven pulley shaft bearing

- Support the inner track of the bearing from the

outside of the hub cover with the specific tool posi-

tioned under the press and insert the driven pulley

axle.

- Refit the oil seal flush with the cover.

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

• Heat the hub cover and insert the bearing with

the specific punch.

• Fit the snap ring with the concave or radial part

on the bearing side.

N.B.

FIT THE BALL BEARING WITH THE SHIELD FACING THE
OIL SEAL.

Specific tooling

020151Y

Air heater

020376Y

Adaptor handle

020439Y

17 mm guide

020358Y

37x40-mm adaptor

Refitting the wheel axle bearing

- Heat the half crankcase on the transmission side

using a thermal gun.

- After lubricating its outer strip, insert the bearing

with the special adapter with the aid of a hammer.

- Refit the seeger ring and the oil seal using the 42

x 47 mm adapter and the handle.

Specific tooling

020151Y

Air heater

020376Y

Adaptor handle

020363Y

20 mm guide

020359Y

42x47-mm adaptor

Runner RST 50 SP

Engine

ENG - 79

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 79 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: