manualshive.com logo in svg

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 54 / 183

Поделиться
Скачать
Gilera Runner RST 50 SP Скачать руководство пользователя страница 54

1

. The lighting system bulbs burn out.

2

. The lighting system bulbs stop working.

3

. The battery overcharges (the main fuse blows).

4

. Non-recharging of the battery.

5

. Non functioning of the turn indicators.

Interventions

BREAKDOWN 1

Replace the regulator due to inefficiency.

BREAKDOWN 2

Check the efficiency of the lamps.

With the vehicle in gear, check the presence of

voltage to the battery on the yellow-black cable of

the light deviator. If there is voltage present, check

the correct voltage distribution of the stator: with-

out disconnecting the connector of the regulator

and with the vehicle in gear, use an alternating

voltage tester to check that the voltage distributed

at the connection between the grey cable and the

black cable is included in the values indicated. If

there are abnormalities, replace the stator.

If the checks made do not show abnormalities, re-

place the regulator.

If replacing the regulator still does not restore prop-

er functioning, make the controls on the connec-

tions of the electrics.

Specific tooling

020331Y

 

Digital multimeter

Characteristic

Voltage distributed at 3000 rpms

25 to 30V

FAULT 3

After checking that there are no short circuits in the system towards the earth, replace the regulator

because it is certainly inefficient and replace it with a protective fuse.

Following the replacement, measure the current and the recharging voltage on the battery end.

Electrical system

Runner RST 50 SP

ELE SYS - 54

Содержание Runner RST 50 SP
























































































































































































Отзывы:

Нет отзывов