manualshive.com logo in svg

GE FVP110, Руководство по обслуживанию

Поделиться
Скачать
GE FVP110 Скачать руководство пользователя страница 286

 FVP 110 Fieldbus Valve Positioner Manual

270

 GE Energy

Repair

If the flameproof apparatus requires repair, turn off the power and 
transport it to a safety (non-hazardous) location. Observe the fol-
lowing points before attempting to repair the apparatus.

❑

Make only such electrical and mechanical repairs as will 
restore the apparatus to its original condition. For the 
flameproof apparatus, the gaps and path lengths of joints 
and mating surfaces, and mechanical strength of 
enclosures are critical factors in explosion protection. 
Exercise great care not to damage the joints or shock the 
enclosure.

❑

If any damage occurs in threads, joints or mating surfaces, 
inspection windows, connections between the transmitter 
and terminal box, shrouds or clamps, or external wiring 
connections which are essential in flameproofness, contact 
GE Masoneilan.
Do not attempt to re-process threaded connections or 
refinish joints or mating surfaces.

❑

Unless otherwise specified, the electrical circuitry and 
internal mechanisms may be repaired by component 
replacement, as this will not directly affect the 
requirements for flame-proof apparatus (however, bear in 
mind that the apparatus must always be restored to its 
original condition). If you attempt to repair the flameproof 
apparatus, company-specified components shall be used.

❑

Before starting to service the apparatus, be sure to check 
all parts necessary for retaining the requirements for 
flameproof apparatus. For this, check that all screws, bolts, 
nuts, and threaded connections have properly been 
tightened.

Prohibition of 
specification changes 
and modifications

Do not attempt to change specifications or make modifications 
involving addition of or changes in external wiring connections.

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды