GE FVP110 Скачать руководство пользователя | Manualshive

Страница: 107 / 292

background image

91

Network Definition

Configuration

The devices within the address range written as

Unused

in Figure 51 cannot be used

on a Fieldbus. For other address ranges, the range is periodically checked to identify
when a new device is mounted. The address range

cannot

become wider, which can

lead to exhaustive consumption of Fieldbus communication performance.

Figure 51

Available Range of Node Addresses

3. Ensure stable operation of Fieldbus by determining the operation parameters and

setting them to the LM devices. The parameters in Table 13 must be set to the worst
case value for all the devices connected to the same Fieldbus. Refer to the
specification of each device for details. Table 13 lists FVP110 specification values.

Table 13

Operation Parameter Values of the FVP110 to be Set to LM Devices

Symbol

Parameters

Description

V (ST)

Slot-Time

Indicates the time necessary for immediate
reply of the device. Unit of time is in octets (256
s).
Set maximum specification for all devices. For
FVP, set a value of 4 or greater.

V (MID)

Minimum-Inter-PDUDelay

Minimum value of communication data
intervals. Unit of time is in octets (256 s). Set
the maximum specification for all devices. For
FVP, set a value of 4 or greater.

V (MRD)

Maximum-Reply-Delay

The worst case time elapsed until a reply is
recorded. The unit is Slot-time; set the value so
that V (MRD) 3V (ST) is the maximum value of
the specification for all devices. For FVP, the
setting must be a value of 12 or greater.

«
...
105
106
107
108
109
...
»

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FVP110

Бренд: VAC Страницы: 16

Бренд: Bifold Orange Страницы: 20

Бренд: AirPower Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды