manualshive.com logo in svg

GE FVP110, Руководство по обслуживанию

Поделиться
Скачать
GE FVP110 Скачать руководство пользователя страница 175

159

 Input Processing 

PID Function Block

Input Processing

The input signal to IN is filtered through a lag filter whose time constant is set in 
PV_FTIME, and then set as the process variable (PV).

Setpoint (SP) Limiters

The path for computing the SP differs depending on the mode. In Cas mode, CAS_IN is 
used for SP. In RCas mode, RCAS_IN is used for SP. If the value of CAS_IN or 
RCAS_IN, whichever is used, is greater than SP_HI_LIM (high limit) or less than 
SP_LO_LIM (low limit), the internal SP is set to the respective limits. When the target 
mode is Auto or Man, and when SP-PV tracking is not specified at the same time, the 
rate of change in the setpoint is also limited (by the values of SP_RATE_UP and 
SP_RATE_DN).

PID Computation

For PID control, the block employs the PV-proportional and PV-derivative type PID 
control algorithm (referred to as the I-PD control algorithm) for Auto and RCas mode. 
This algorithm measures control stability against sudden changes in the setpoint, such 
as when you enter a new setpoint value. At the same time, the IPD algorithm ensures 
excellent controllability by performing proportional, integral, and derivative control 
actions in response to changes of characteristics in the controlled process, changes in 
load, and occurrences of disturbances.

For Cas mode, PV-derivative type PID control algorithm (referred to as the PI-D control 
algorithm) is employed in order to obtain better performance against the changes in the 
setpoint.

The algorithm is automatically changed by the block according to the mode. A basic 
form of each algorithm is expressed in the equation below.

In Auto / RCas mode

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды