manualshive.com logo in svg

GE FVP110, Руководство по обслуживанию

Поделиться
Скачать
GE FVP110 Скачать руководство пользователя страница 241

225

 Descriptions for LM Parameters 

Link Master Functions

LiveListStatusArrayVariable

A 32-byte variable, in which each bit represents the status of whether a device on the 
same segment is live or not.

The leading bit corresponds to the device address 0x00, and final bit to 0xFF. The value 
of LiveListStatusArrayVariable in the case where devices having the addresses 0x10 
and 0x15 in the fieldbus segment is shown below.

MaxTokenHoldTimeArray

An 8 64 byte array variable, in which each set of 2 bytes represents the delegation time 
(set as an octet time) assigned to a device. The delegation time denotes a time period 
that is given to a device by means of a PT message sent from the LAS within each 
token circulation cycle.

The leading 2 bytes correspond to the device address 0x00, and the final 2 bytes to the 
device address 0xFF. Specify the subindex to access this parameter.

BootOperatFunctionalClass

Writing 1 to this parameter in a device and restarting the device causes the device to 
start as a basic device. On the contrary, writing 2 to this parameter and restarting the 
device causes the device to start as an LM.

CurrentLinkSettingRecord and ConfiguredLinkSettingsRecord

CurrentLinkSettingRecord indicates the bus parameter settings currently used. 
ConfiguredLinkSettingsRecord indicates the bus parameter settings for use when the 
device becomes the LAS. When a device is the LAS, its CurrentLinkSettingRecord and 
ConfiguredLinkSettingsRecord have the same values.

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды