manualshive.com logo in svg

GE FVP110, Руководство по обслуживанию

Поделиться
Скачать
GE FVP110 Скачать руководство пользователя страница 189

173

 Signatures and Relevant 

Diagnostics

Scan Time [seconds]
Deviation Margin [%]
Sampling Rate [milliseconds] (not used in this function)

Performing measurements sets the pressure data in 
SIGN_DATA_X and the position data (%) in SIGN_DATA_Y.

High Resolution 
Actuator Signature *1

The high-resolution actuator signature is the valve 
input-to-position characteristics, measured with high resolution 
while sampling data at the specified time rate. Up to 100 data 
values can be stored in the FVP100 memory. After this limit is 
reached during measurement, the stored data is overwritten 
from the leading data in order. Using ValVueFF, you can con-
tinue measurement while uploading the measured data. The 
following is settable for EXT_ACT_SIGN_SET:

Lower Setpoint [%] (point to start the measurement)
Upper Setpoint [%] (point to finish the measurement)
Recommended Scan Time [seconds] (not used in this function)
Scan Time [seconds]
Deviation Margin [%]
Sampling Rate [milliseconds]

The sampling rate can be set within the range of 200 through 
1000 milliseconds. The total number of measured samples is 
obtained by the following formula:

Scan time / sampling rate  1000 [points]

Performing measurements sets the pressure data in 
SIGN_DATA_X and the position data (%) in SIGN_DATA_Y.

Step Response Test

The step response test measures time-series changes in the 
valve position in response to a sudden change (step) in the 
positioner setpoint from the preset initial setpoint to the destina-
tion setpoint. The following is settable for STEP_RESP_SET:

Initial Setpoint [%]
Destination Setpoint [%]
Sampling Rate [milliseconds]
Number of Samples [points]

The sampling rate can be set within the range of 20 through 
1000 milliseconds (corresponding to the measurement period 
of 0.4 through 600 seconds). The number of samples can be 
set to up to 600.

Performing measurements sets the positioner setpoints in 
SIGN_DATA_X and the position data (%) in SIGN_DATA_Y.

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды