manualshive.com logo in svg

GE FVP110, Руководство по обслуживанию

Поделиться
Скачать
GE FVP110 Скачать руководство пользователя страница 282

 FVP 110 Fieldbus Valve Positioner Manual

266

 GE Energy

Electrical Apparatus of Flameproof Type of Explosion- Protected 
Construction

Electrical apparatus which is of flameproof construction is subjected to a type test and 
certified by the Japanese Ministry of Labour aiming at preventing explosion caused by 
electrical apparatus in a factory or any location where inflammable gases or vapors may 
be present. The flameproof construction is of completely enclosed type and its enclosure 
shall endure explosive pressures in cases where explosive gases or vapors entering the 
enclosure cause explosion. In addition, the enclosure construction shall be such that 
flame caused by explosion does not ignite gases or vapors outside the enclosure.

In this manual, the word 

flameproof

 is applied to the flameproof equipment combined with 

the types of protection 

e, o, i, and d

 as well as flameproof equipment.

Terminology

The permissible sizes of gaps between joint surfaces, the path 
length of a joint surface and the number of joint threads are deter-
mined by such factors as the enclosure’s internal volume, joint 
and mating surface construction, and the explosion classification 
of the specified gases and vapors.

Enclosure

An outer shell of an electrical apparatus, which encloses live 
parts and thus is needed to configure explosion-protected con-
struction.

Shroud

A component part designed so that the fastening of joint surfaces 
cannot be loosened unless a special tool is used.

Enclosure internal 
volume

This is indicated by:— the total internal volume of the flameproof 
enclosure minus the volume of the internal components essential 
to equipment functions.

Path length of joint 
surface

On a joint surface, the length of the shortest path through which 
flame flows from the inside to outside of the flameproof enclosure.

This definition cannot be applied to threaded joints.

Gaps between joint 
surfaces

The physical distance between two mating surfaces, or differ-
ences in diameters if the mating surfaces are cylindrical.

Содержание FVP110





































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды