Galaxy Control Systems 635 Series Скачать руководство пользователя страница 33

Страница: 33 / 212

635/600-SERIES HARDWARE INSTALL GUIDE

Chapter-Page

1-20

Table 6: BOARD COMPATIBILITY CHART for SG 10/11

(

Tables 7 & 8 for SG-9 or lower

)

WHEN IS UPGRADING SG SOFTWARE REQUIRED ?…



if an

SG version

is noted, then that is the minimum version of SG required to support that board/feature



if the

no version

is listed, then any version of SG 10 supports the feature.

WHEN IS UPGRADING HARDWARE REQUIRED ?…



Installing Wireless Readers, IP Readers – you must upgrade to 635 CPU and 635-DSI



Installing 635-Input Module – you must upgrade to 635 CPU and 635-DSI



Installing a Galaxy 485 Remote Door Module – You must upgrade to 635-CPU, 635-DRM, and 635-DSI.



Installing newer destination-driven elevator systems, then you must install all 635-model hardware.

•

600-model boards can interoperate with 635-model boards in the same system and within the same control panel

•

You can replace older 600-model boards with new 635-model boards as needed.

•

The older 600-model boards do not support the newer hardware interfaces and features supported by the 635.

635-SERIES CONTROLLER

600-SERIES CONTROLLER

635 CPU Board

Processor

600 CPU Board

–

Processor

•

Operates in same loop /system with 600 CPUs

•

Supports all 635 & 600 daughter boards

•

Supports all 635-series

RS485

Modules

•

Supports all 600-series

RS485

Modules – restrictions apply

•

Supports Destination-driven elevator systems

•

Supports Card Tour Board

•

Operates in same loop /system with 635 CPUs

•

Compatible/Supports all 600 daughter boards

•

Supports 635 DRM (Reader board)

•

Supports 600 Output/Elevator Modules on 600 DSI

•

Destination-driven elevator systems and Card Tour are not supported.

635 DAUGHTER BOARDS

600 DAUGHTER BOARDS

635 DAUGHTER BOARDS

600 DAUGHTER BOARDS



600 DIO Board



600 DIO Board

635 DRM Reader

Board

600 DPI Reader Board

635 DRM Reader

Board

600 DPI Reader Board

635 DSI Serial Board

600 DSI Serial

Board

635 DSI Serial Board

600 DSI Serial

Board

•

600 Output Module (general

output or elevator control)

•

LCD Clock unit

•

Schlage PIM 485 ODT (legacy)

•

600 Output Module (general

output or elevator control)

•

LCD Clock unit

•

Schlage PIM 485 ODT (legacy)

•

600 Output Module (general

output or elevator control)

•

LCD Clock unit

•

Schlage PIM 485 ODT (legacy)

•

600 Output Module (general

output or elevator control)

•

LCD Clock unit

•

Schlage PIM 485 ODT (legacy)

•

Assa Abloy Aperio (SG 10.1)

•

Assa Abloy Aperio (SG 10.1)

<< Not supported on 600-CPU

•

Salto Salis Wireless (SG 10.2)

•

Salto Salis Wireless (SG 10.2)

<< Not supported on 600-CPU

•

Schlage AD-300 (SG 10.2)

•

Schlage AD-400 Wifi (10.2)

•

or Mix AD-300/AD-400 (10.2)

•

Schlage AD-300 (SG 10.2)

•

Schlage AD-400 Wifi (10.2)

•

or Mixed AD-300/AD-400 (10.2)

•

Assa IP Readers (SG 10.4)

•

Assa IP Readers (SG 10.4)

•

635 Input Module (SG 10.4)

<< Not supported on 600-DSI

•

635 Remote Door DRM (10.4)

<< Not supported on 600-DSI

COMPATIBLE MODULES (RS-485 multi-drop)

600 Elevator/Output Module

( using DSI )

600 Elevator/Output Module

( using DSI )

635 Door Module (using 635 CPU & DSI, SG 10.3)

<< 635 Door Module not supported on 600 CPU

635 Input Module (using 635 CPU & DSI, SG 10.4)

<< 635 Input Module not supported on 600 CPU

Содержание 635 Series





















































































































































































































Результаты поиска

Содержание 635 Series

Отзывы:

Похожие инструкции для 635 Series

Бренды по названию

Популярные бренды

Galaxy Control Systems 635 Series, Руководство по установке и настройке

Результаты поиска

Содержание 635 Series

Отзывы:

Похожие инструкции для 635 Series

Бренды по названию

Популярные бренды