Franklin Fueling Systems NANOVAPOR NV-SS ST-1000 Скачать руководство пользователя страница 20

Страница: 20 / 60

Description of system components

This section describes each component of the NV-ST-1000 TankSafe™ Delivery Unit in detail. The
purpose, location, and specifications of each component are included.

Part numbers

Description

Part Number

TankSafe™, 5 Liter Container

NV-TS-5

ST-1000 Delivery System

NV-ST-1000

Vent Section (Top) (1x2 m long)

NV-001

Vent Section (Middle) (1x1 m long)

NV-001A

Vent Section (Bottom); comes with Sample Boss (1x2 m long)

NV-002

4" Drop Tube - Single Outlet (1.5 m long)

NV-003

4" Drop Tube - Double Outlet (1.5 m long)

NV-004

3" Drop Tube - Single Outlet (1.5 m long)

NV-005

3" Drop Tube - Doulbe Outlet (1.5 m long)

NV-006

2" Drop Tube - Single Outlet (1.5 m long)

NV-007

198mm - 4" Female Camlock (Cone-Shaped) Adapter

NV-008

4" Tank Adapter; BSPP Male - 3" BSPP Female

NV-009

3" Tank Adapter; BSPP Double Male Barrel Nipple

NV-009a

4" Tank Adapter; Male Camlock - 4" BSPP Female

NV-009b

200 mm x 3 m Flex Duct, Wire Heliz

NV-010

Spiral Hose Bridging Clamp (1 set of 2)

NV-010a

200mm x 6m Flex Duct, Wire Heliz

NV-011

Spiral Hose Bridging Clamp

NV-011a

Air Line Whip Checks (1 set of 4)

NV-012

Mini Rocket

NV-013

210mm Anti-Static Lay Flat Duct x 50 m roll (Blk)

NV-014

150mm Anti-Static Lay Flat Duct x 75 m roll (Pink)

NV-015

*Large Rocket (vapor collection)

NV-016

Diffuser Drop Tube 4" Insert

NV-017

Diffuser Drop Tube 3" Insert

NV-018

Diffuser Drop Tube 2" Insert

NV-019

ST-1000 Spare Pack

NV-020

Air Filter Bowl

NV-020a

Filter Bowl O-Ring

NV-020b

Filters (1 set of 2)

NV-020c

Claw Coupling Rubber Seal (1 set of 4)

NV-020d

All Tank Access (ATA) kit; fuel & sludge removal pipe for 20 m

Tank

NV-022

All Tank Access (ATA) kit; fuel & sludge removal pipe for 30 m

Tank

NV-022a

All Tank Access (ATA) kit; fuel & sludge removal pipe for 40 m

Tank

NV-022b

All Tank Access (ATA) kit; fuel & sludge removal pipe for 50 m

Tank

NV-022c

All Tank Access (ATA) kit; fuel & sludge removal pipe for 80 m

Tank

NV-022d

Содержание NANOVAPOR NV-SS ST-1000





























































Результаты поиска

Содержание NANOVAPOR NV-SS ST-1000

Отзывы:

Franklin Fueling Systems NANOVAPOR NV-SS ST-1000, Инструкция по установке и эксплуатации, Страница: 20 / 60

Результаты поиска

Содержание NANOVAPOR NV-SS ST-1000

Отзывы: