Extreme Networks ExtremeWare 7.3.0 Скачать руководство пользователя страница 641 | Manualshive

Страница: 641 / 2254

background image

configure packet-mem-scan-recovery-mode

ExtremeWare Software 7.3.0 Command Reference Guide

641

configure packet-mem-scan-recovery-mode

configure packet-mem-scan-recovery-mode [offline | online] [msm-a | msm-b |

<slot number>]

Description

Configures packet memory scanning and the recovery mode setting on a BlackDiamond module.

Syntax Description

Default

Disabled.

Usage Guidelines

Use this command to scan and check the health of an individual module rather than the overall system.

This command overrides the system health check auto-recovery setting. If you have the system health
check alarm level configured, the individual packet memory scanning configuration is ignored.

This command is only effective if the system health check is configured for auto-recovery. If you have
the system health check configured for auto-recovery, and you configure packet-mem-scan-recovery, you
can define a specific slot’s behavior if an error is discovered.

To configure the system health check for auto-recovery, use the

configure sys-health-check

auto-recovery <number> [offline | online] | alarm-level [card-down | default | log |

system-down | traps]

command.

The alarm-level and auto-recovery options are mutually exclusive; configuring an alarm-level disables
auto-recovery, and configuring auto-recovery overrides the alarm-level setting.

offline

Specifies that a faulty BlackDiamond module is taken offline and kept offline if
one of the following occurs:

•

More than eight defects are detected.

•

Three consecutive checksum errors were detected by the health checker,
but no new defects were found by the memory scanning and mapping
process.

•

After defects were detected and mapped out, the same checksum errors
are again detected by the system health checker.

online

Specifies that a faulty module is kept online, regardless of how many errors
are detected.

msm-a

Specifies the MSM module installed in slot A.

msm-b

Specifies the MSM module installed in slot B.

slot number

Specifies a module installed in a slot.

«
...
639
640
641
642
643
...
»

Содержание ExtremeWare 7.3.0















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeWare 7.3.0

70 MC - ZR70MC MiniDV Digital Camcorder

Бренд: Canon Страницы: 57

RESIDENT CONSULTANT

Бренд: Juniper Страницы: 4

Бренд: TC Electronic Страницы: 12

Бренд: Waves Страницы: 20

Бренд: ICP Страницы: 77

Бренд: Qlogic Страницы: 180

ANTI-VIRUS - FOR FREEBSD-OPENBSD-BSDI MAIL SERVER

Бренд: KAPERSKY Страницы: 295

ZENWORKS APPLICATION VIRTUALIZATION - V8.0.3 INTEGRATION AND STREAMING GUIDE

Бренд: Novell Страницы: 36

ZENworks 10 Configuration Management

Бренд: Novell Страницы: 32

ZENWORKS LINUX MANAGEMENT 7.2 IR2 - 07-20-2009

Бренд: Novell Страницы: 134

ZENWORKS 10 CONFIGURATION MANAGEMENT SP3 - COMMAND LINE UTILITIES REFERENCE 10.3 30-03-2010

Бренд: Novell Страницы: 200

OPEN WORKGROUP SUITE SMALL BUSINESS EDITION 2.0

Бренд: Novell Страницы: 77

LINUX ENTERPRISE REAL TIME 10 SP1

Бренд: Novell Страницы: 7

LINUX ENTERPRISE SERVER 10 - STORAGE ADMINISTRATION GUIDE FOR EVMS

Бренд: Novell Страницы: 93

OPEN ENTERPRISE SERVER 2 SP 2 - CLUSTER SERVICES 1.8.7 FOR LINUX

Бренд: Novell Страницы: 254

LINUX ENTERPRISE DESKTOP 10

Бренд: Novell Страницы: 9

IFOLDER 3.6 - SECURITY ADMINISTRATION

Бренд: Novell Страницы: 22

LINUX ENTERPRISE 11 - SUBSCRIPTION MANAGEMENT TOOL GUIDE 10-02-2009

Бренд: Novell Страницы: 236

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды