Extreme Networks ExtremeWare 7.3.0 Скачать руководство пользователя страница 701 | Manualshive

Страница: 701 / 2254

background image

enable sys-health-check

ExtremeWare Software 7.3.0 Command Reference Guide

701

enable sys-health-check

enable sys-health-check

Description

Enables the BlackDiamond system health checker.

Syntax Description

This command has no arguments or variables.

Default

Enabled.

Usage Guidelines

The system health checker tests I/O modules, MSM modules, and the backplane by forwarding packets
every 4 seconds. Additional checking for the validity of these packets is completed by performing a
checksum.

By isolating faults to a specific module, MSM, or backplane connection, the system health checker
prevents corrupted packets from being propagated to the CPU, upper layer modules, or the rest of your
network. If you observe a failure, please contact Extreme Technical Support.

Depending on how you have configured the system health checker, failed system health checks may
generate critical error messages in the syslog, and may also send a trap and/or shut down the system.
The system health checker will continue to periodically forward test packets to failed components. If
auto-recovery is configured, the system will attempt to automatically reset the faulty module and bring
it back online.

In ExtremeWare versions prior to 6.2, you cannot use both mirroring and the system health checker at
the same time. If you configure mirroring with the system health checker enabled, the health checker
will indicate that it has been disabled by sending a message to the syslog. In version 6.2 or later, this
restriction does not apply.

To configure the health checker, use the following command:

configure sys-health-check [alarm-level [card-down | default | log | system-down |

traps] | auto-recovery <number of tries>]

The alarm-level and auto-recovery options are mutually exclusive; configuring an alarm-level disables
auto-recovery, and configuring auto-recovery overrides the alarm-level setting.

Example

The following command enables the BlackDiamond system health checker:

enable sys-health-check

History

This command was first available in ExtremeWare 6.2.

«
...
699
700
701
702
703
...
»

Содержание ExtremeWare 7.3.0















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeWare 7.3.0

DRAGON NATURALLYSPEAKING 7

Бренд: ScanSoft Страницы: 222

Бренд: M-Audio Страницы: 32

Бренд: VeriFone Страницы: 25

8.5 EMAIL SERVER EDITION - V 85.4

Бренд: AVG Страницы: 52

Бренд: Savin Страницы: 71

Бренд: FARONICS Страницы: 4

WINSELECT STANDARD

Бренд: FARONICS Страницы: 36

Бренд: Denon Страницы: 2

Бренд: Texas Instruments Страницы: 52

Бренд: MGI Страницы: 19

Бренд: AMX Страницы: 53

FLASH 8-DEVELOPING FLASH LITE 2.X

Бренд: MACROMEDIA Страницы: 94

WebSphere Adapters

Бренд: IBM Страницы: 226

DEEP FREEZE SERVER STANDARD

Бренд: FARONICS Страницы: 24

Бренд: Quantum Страницы: 142

REGISTRYBOOSTER 2010 - V1

Бренд: UNIBLUE Страницы: 11

Storage Manager

Бренд: NEC Страницы: 134

Бренд: Oki Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды