Estun pronet series Скачать руководство пользователя страница 73

Страница: 73 / 193

ProNet

Series

AC Servo User's Manual

- 71 -

4.3.2 Switching the Servomotor Rotation Direction

The rotation direction of the servomotor can be switched without changing the reference pulse to the servo drive or the

reference voltage polarity.

This causes the rotation the servo motor shaft is rotating to change. The output signal polarity, such as the encoder pulse

output and the analog monitor signal from the servo drive do not change.

The standard setting for “forward rotation” is counterclockwise as viewed from the servomotor load end.

Parameter Name

Reference

Forward reference

Reverse reference

Pn001

□□□

Standard setting

(CCW=forward)

(factory setting)

PBO

CCW

PAO

Encoder pulse division output

PAO

PBO

Encoder pulse division output

□□□

Reverse rotation

mode

(CW=forward)

PAO

PBO

Encoder pulse division output

CCW

PAO
PBO

Encoder pulse division output

The direction of P-OT and N-OT change. For Pn001=b.

□□□

0(standard setting), counterclockwise is P-OT. For

Pn001=b.

□□□

1(reverse rotation mode), clockwise is P-OT.

Содержание pronet series


































































































































































































Результаты поиска

Содержание pronet series

Отзывы:

Похожие инструкции для pronet series

Бренды по названию

Популярные бренды

Estun pronet series, Руководство пользователя

Результаты поиска

Содержание pronet series

Отзывы:

Похожие инструкции для pronet series

Бренды по названию

Популярные бренды