Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 62

Страница: 62 / 124

AOX determination

multi X 2500



Create an analysis sequence.

Enter the sample ID for all samples in the field N

AME

Confirm the entry with [OK].



Click the [S

TART MEASUREMENT

] button.



The prepared analysis sequence is processed.

14.

Follow the prompts in the control and analysis software multiWin and insert the

one sample after the other through the oxygen sluice into the combustion tube.

Confirm each inserted sample with [OK].



The loaded activated carbon is combusted in the oxygen stream and turned

into hydrogen halide, carbon dioxide and water. After drying the pyrolysis gas

the halide is determined in micro-coulometrically in the chlorine module.

6.2.4

Carrying out measurements with the autosampler autoX 36 / autoX 36d

WARNING

Concentrated sulfuric acid can cause severe chemical burns! Wear appropriate

protective clothing when working at the sulfuric acid container. Observe all

specifications in the safety data sheet!

Connect the autosampler to the "sampler" connection on the rear panel of the
multi X 2500 using the interface cable.

Fill the sulfuric acid container (vertical) with fresh sulfuric acid every day.

If necessary, remove any used quartz containers from the open combustion tube.

When using the autosampler autoX 36d (with ejection function):

Use tweezers to place the quartz crucible into the combustion

tube.
The quartz crucible prevents the quartz wool to form lumps

when it directly touches the hot activated carbon. This would

prevent it from filtering ashes and soot from the measuring

gas stream.

Remove the top cover of the analyzer and insert the autosampler without rack into

the opening.

Preparing the measuring cell:



Fill the measuring cell with fresh electrolyte solution every day.

Measuring cell "sensitive": 15 to 20 ml



Insert the magnetic stirring rod into the measuring cell. Attach the cover and

tighten it using the three knurled head screw.



Insert the combined electrode and connect it electrically. Electrically connect
the measuring cell.

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды