Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 68

Страница: 68 / 124

AOX determination

multi X 2500

Switch on the multi X 2500. Open the gas supply.

Close the pneumatic seal to the auto-protection assembly.

To do this, move the toggle switch (1) down.



This completes the installation of the combustion tube

and the locking of the auto-protection assembly.

Preparing the chlorine module:

WARNING

Concentrated sulfuric acid is used as desiccant. The concentrated acid can cause severe

chemical burns! Wear protective clothing when working at the sulfuric acid container.

Observe the specifications in the safety data sheet!

NOTICE

Risk of damaging the intake pump of the chlorine module!
Make sure to properly connect the gas supply in the measuring cell when using the

multi-purpose combustion tube. Never connect the measuring cell to the intake pump

via the olive-tip suction adapter and the hose. Otherwise, electrolyte will be drawn into

the pump unit.

The hose of the transfer line is connected to the connector at the terminal of the
sulfuric acid container with outlet using a banjo bolt with conical nipple. Make sure

that the conical nipples are seated correctly!

Fig. 43 Connection transfer line – sulfuric acid container with outlet

1 Gas transfer line
2 Banjo bolt

3 Connector sulfuric acid container
4 Hose sulfuric acid container

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды