Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 43

Страница: 43 / 124

multi X 2500

Installation and commissioning

4.1

Installation conditions

See "Technical data" on page 122 for information on the ambient conditions of the

installation location. It may be necessary to control the temperature in the room.

The installation location should have the characteristics of a chemical laboratory. It

must meet the following conditions:



Atmosphere free from hydrocarbons, halogens, sulfur compounds and nitrogen
oxides



Atmosphere with low dust levels



No vibrations



Smoking must be prohibited in the room where the multi X 2500 is operated

The site for installing the multi X 2500 must meet the following requirements:



Free from caustic vapors in close proximity of the multi X 2500

Connections and assemblies of the device may corrode.



Free from draft air; do not install the device close to windows or doors



Away from electromagnetic sources of interference



No direct sunlight and away from radiant heaters



The front door and air vents must not be obstructed by other equipment or
furnishings



Keep a safety distance of at least 20 cm from the rear of the device to other

equipment or walls

4.2

Energy supply

Caution

The multi X 2500 must only be connected to a power outlet which is properly

grounded in accordance with the voltage specifications on the type plate!

The installation of the electrical equipment of the laboratory must comply with the

standard DIN VDE 0100. After the connection point an electrical current in accordance

with the standard IEC 38 must be available.

Electrical connection data, see "Technical data", p. 122 ff.

Ambient conditions

Laboratory conditions

Requirements with
regard to the installation
location

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды