Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 76

Страница: 76 / 124

EOX determination

multi X 2500

Horizontal operating mode

Vertical operating mode

Open the gas supply.

Connect hose no. 3 (1) and hose no. 4 (2) to the combustion tube. To do this,
insert the hose ends into the angled adapters on the combustion tube.

NOTICE! Do not push the hoses and the connectors beyond the branch length of

the angled adapter. Only then, the gas will be able to flow freely.

Horizontal operating mode

Vertical operating mode

Plug in the flame sensor (3) to the connection, if used.

Screw a screw cap with septum to the combustion tube.

Close the pneumatic seal to the auto-

protection assembly. To do this, move

the toggle switch (1) down.



The combustion tube is now locked

in the auto-protection assembly.

In vertical operating mode, put the cover at the top back into place.

10.

Connect a sample introduction module.

For the EOX determination, the sulfuric acid container with outlet is inserted into the
chlorine module. Refer to chapter "AOX determination in horizontal operating mode",

p. 65 for information on the installation of the sulfuric acid container.

Prepare the chlorine
module

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды