Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 11

Страница: 11 / 124

multi X 2500

Safety instructions

2.4

Safety instructions - operation

2.4.1

General

The operator of the analyzer must make sure before each commissioning that the
condition of the analyzers including the safety equipment is sound. This applies in

particular after each modification or extension of the analyzer or its repair.
Observe the following notes:



The analyzer must only be operated if all protective equipment (e.g. covers, drip

pans for chemicals, side walls and doors) are in place, properly installed and fully

operational.



The sound condition of the protection and safety equipment must be checked

regularly. Any defects must be corrected as soon as they occur. Protective and

safety equipment must never be removed, modified or switched off during
operation.



Free access to the device switch on the rear panel of device must always be ensured

during operation.



The ventilation equipment on the multi X 2500 and the chlorine module must be in

good working condition. Covered ventilation grilles or slits etc. may cause the

device to break down or may cause damage to it.



The furnace operates with temperatures of up to 1100 °C. The hot components

must not be touched during or directly after the operation of the analyzer.



Caution when handing quartz glass and glass parts. Risk of broken glass and
therefore risk of injury!



Prevent any ingress of liquids into the interior of the device. Liquids may cause a

short circuit inside the housing.



Keep all combustible materials away from the analyzer.

The multi X 2500 may not be operated in an explosive environment.



Smoking or naked flames are prohibited in the room where the multi X 2500 is
operated!



The operating personnel has to be familiar with the location of the fire-fighting

equipment in the operating room of the analyzer.

2.4.2

Safety instructions - electrical equipment

Contact with live components may cause death, serious injury or painful electrical

shock. Life-threatening electrical voltages may occur in the right part of the
multi X 2500 behind the control electronics cover.

Protection against
explosion and fire

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды