Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 50

Страница: 50 / 124

Operation

multi X 2500

5.2

Switching off the analyzer

WARNING

Concentrated sulfuric acid can cause severe chemical burns! Wear protective clothing

when working at the sulfuric acid container. Observe all specifications in the safety

data sheet!

Exit the multiWin control and analysis software. Allow the device to cool down.

NOTICE! Wait for a moment before switching off the basic device and the chlorine

module. Otherwise, the device may overheat when the ventilation is switched off

with the device.

Use the device switch to switch off the basic device and the chlorine module.

Remove the electrode from the measuring cell and store it in accordance with the

applicable regulations (

→

"combined electrode", p. 93).

Empty the measuring cell and clean it (

→

"Servicing the measuring cell", p. 92).

After the device has cooled down, remove the sulfuric acid container from the basic

device and clean it.

NOTICE

Do not cut the gas supply before the sulfuric acid has been drained or the device has

cooled down. A vacuum may build up when the device cools down which may draw

sulfuric acid into the gas transfer line. As long as the gas supply is open, the argon

safety bypass on the auto-protection assembly prevents this from happening.

Exit the multiWin control and analysis software.

Remove the gas transfer line from the sulfuric acid container in the chlorine
module and drain the sulfuric acid from the sulfuric acid container (

→

"Changing

the sulfuric acid and cleaning the sulfuric acid container with outlet", p. 101).

WARNING! Sulfuric acid can cause severe chemical burns. The grinding of the
sulfuric acid container and the hose which is immersed in the sulfuric acid container

may contain residual acid.

Allow the analyzer to cool down. After that, switch off the multi X 2500 and the
chlorine module using the mains switch. Cut the gas supply.

Remove the electrode from the measuring cell and store it in accordance with the

applicable regulations (

→

"Clean and store the electrode", p. 105).

Empty the measuring cell and clean it (

→

"Maintaining the measuring cell",

p. 104).

Standard version

Optional versions

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды