Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 124

background image

Basic information

multi X 2500

8

1.2

Intended use

The multi X 2500 analyzer is used for the quantitative determination of adsorbable
(AOX), extractable (EOX) or purgeable (POX) organic halogenated compounds in

aqueous samples, soils and sewage sludge. The device is conceived for the analysis of

drinking water, industrial water, surface water and waste water.
The analyzer may also be used to determine the total chloride content in solid and

liquid organic matrices (TX/TOX). When determining the total chlorine content, the

device will determine the bromine and iodine content of the sample as well. Fluorine is
not detected. There is the option to upgrade the multi X 2500 by a TOC module. This

allows determining the carbon content (TC, TOC, TIC) in aqueous samples.
The device must only be used with argon and oxygen as a carrier gas.
The multi X 2500 analyzer must only be used for the methods described in this user

manual. Any other use is not as intended! Only the operator is liable for any damages

that result from this.

1.3

Warranty and liability

The warranty duration and liability comply with the legal requirements and the
provisions in the general terms and conditions of Analytik Jena.
Deviations from the intended use described in this user manual result in limitations of

warranty and liability in the event of a damage. Damage to wearing parts is not
included in the warranty.
Warranty and liability claims are excluded for personal injury and property damage

due to one or several of the following causes:



use of the multi X 2500 other than intended



improper commissioning, operation and maintenance of the multi X 2500



modifications to the multi X 2500 without prior consultation with Analytik Jena



operation of the multi X 2500 with faulty safety equipment or improperly fitted

safety and protection equipment



inadequate monitoring of the equipment components subject to wear



use of other than original spare parts, wearing parts or consumables



improper repairs



faults due to the non-observance of this user manual

«
...
6
7
8
9
10
...
»

Содержание Analytik Jena Multi X 2500





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Analytik Jena Multi X 2500

Бренд: Icare Страницы: 3

HYDROMETTE BL Compact TF-IR 2

Бренд: GANN Страницы: 40

Бренд: Gamry Страницы: 16

Бренд: Kawai Страницы: 8

Бренд: E-Mon Страницы: 72

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Panametrics Aurora H2O

Бренд: Baker Hughes Страницы: 92

Бренд: phase II Страницы: 11

Amplitude T Series

Бренд: OTOVATION Страницы: 15

Бренд: Harken Страницы: 2

Бренд: Huvitz Страницы: 58

Бренд: Sonel Страницы: 56

Бренд: Westfalia Страницы: 2

Бренд: National Instruments Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды