Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 112

Страница: 112 / 124

Fault removal

multi X 2500

112

Furnace temperature is outside tolerance limits or target temperature is not reached
Cause

Solution



Temperature controller faulty



Electronics error



Report to customer service

Process gases (inlet flow) are not present
Cause

Solution



Gas supply not connected



Primary gas pressure too low



Gas supply leaking



No method loaded



Gas box faulty



Connecting the gas supply



Set primary gas pressure at the delivery point to

between 4 and 6 bar



Check gas supply



Load method



Report to customer service

Target flow at the outlet to the detector module too low
Cause

Solution



Connection between hose, angled adapter and

combustion tube not correct



Pneumatic seal in the auto-protection assembly does

not seal combustion tube



Septum sits incorrectly at the inlet of the combustion

tube or is leaking



Connection transfer line to the auto-protection

assembly leaking



In the horizontal operating mode transition coupling

tube to ABD leaking



Check connection and ensure correct fit at the

connection points



Check argon supply, open the pneumatic seal with the

toggle switch



Check position of the septum, insert new septum if

necessary



Check connection



Check sealing of the coupling element

check alignment between combustion tube, coupling,

ABD, hand-tighten the connection

Gas escapes from pneumatic seal (audible hiss)
Cause

Solution



Screw connection of the gas connection for hose no. 8 is

loose



Pneumatic seal faulty



Tighten screw connection and lock nut



Replace pneumatic seal (

→

chapter 10.4.3, p. 96)

Auto-protection assembly does not heat up
Cause

Solution



Valve assembly not connected



Heating or temperature controller defective



Plug in the connector (3 in Fig. 6, p. 21)



Inform customer service

Auto-injector is not recognized
Cause

Solution



Auto-injector and autoX 112 are switched on at the

same time



Switch off the autosampler autoX 112

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды