Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 96

Страница: 96 / 124

Maintenance and care

multi X 2500

10.4.3

Servicing the auto-protection assembly

CAUTION

There is a risk of burns on the combustion furnace! Only install the auto-protection

assembly when the device is cold or allow the device to cool down sufficiently!

NOTICE

Always switch off all components of the multi X 2500 before electrically connecting

them! Connecting or disconnecting electrical contacts may damage the sensitive

electronic components of the multi X 2500.

For the following maintenance work the auto-protection assembly must be removed
from the multi X 2500.
1.

Disconnect the gas transfer line from the sulfuric acid container with outlet in the

chlorine module.

Exit the multiWin software and allow the analyzer to cool down.

Use the mains switch to switch off the multi X 2500 and the chlorine module and

cut the gas supply.

If not already done, tilt the combustion furnace into horizontal position.

Open the pneumatic seal on the auto-protection assembly.

To do this, move the toggle switch (1) up.

Pull on the multi-purpose combustion tube to remove it a

little from the combustion furnace.

Pull the electrical connector for the auto-protection

assembly (2) from the connection.

Detach hose no. 8 (1) from the connection.

Remove hose no. 11 (2). Push down the ring of the plug-in

connector to do this.

Detach the gas transfer line (3) from the connection at the

side.

Removing the auto-
protection assembly

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды