Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 70

Страница: 70 / 124

AOX determination

multi X 2500

Attach a funnel to the sulfuric acid container. Fill 15 ml of

concentrated sulfuric acid into the sulfuric acid container.

Remove the funnel.

Fit the safety attachment (7) to the sulfuric acid container

and attach the safety clip.

10.

Connect the measuring gas hose (8) to the electrode (see

below).

Inserting the measuring cell:

NOTICE

Risk of damaging the intake pump of the chlorine module!
Make sure to properly connect the gas supply in the measuring cell when using the

multi-purpose combustion tube. Never connect the measuring cell to the intake pump

via the olive-tip suction adapter and the hose. Otherwise, electrolyte will be drawn into

the pump unit.

The measuring cells "sensitive" and "high concentration" are inserted to the chlorine
module as follows:

Insert the measuring cell "sensitive" with lid into the chlorine module. If used, insert
the measuring cell "high concentration" into the chlorine module

(TX determination).

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды