Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 101

Страница: 101 / 124

multi X 2500

Maintenance and care

101

Pull hose no. 3 (1) and hose no. 4 (2) from the angled

adapters at the combustion tube. If used, remove the flame

sensor from the connection (3).

Carefully remove the combustion tube from the furnace.

10.

Check the combustion tube for excessive crystallization,

cracks and blow-outs. Only reuse intact combustion tubes.

11.

Clean the combustion tube with detergent and a brush or cellulose, if necessary.

The combustion tube can also be cleaned by burning off deposits in a muffle

furnace or with a suitable burner flame.

Refer to "Inserting the multi-purpose combustion tube" S. 67 for information on the

reinstallation of the multi-purpose combustion tube.

10.4.5

Changing the sulfuric acid and cleaning the sulfuric acid container with outlet

WARNING

Concentrated sulfuric acid can cause severe chemical burns! Wear protective clothing

when working at the sulfuric acid container. Observe all specifications in the safety

data sheet!

The sulfuric acid absorbs the water that is produced during the combustion process. If

the acid content falls below 85 % the sulfuric acid can no longer sufficiently dry the

reaction gas. As a result, the measured AOX contents will be too low and widely
scattered. For this reason, the sulfuric acid must be replaced once per day. High sample

throughput may require more frequent replacement.

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды