manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 99 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 99

ER5000

 — 

99

Installation Variations

Feedback Wiring Variations

4–20 mA External Feedback, Ground Referenced Input, 
Feedback Signal Monitored by PC or PLC A/D Card 

Figure 35 show how the feedback signal can be monitored 
using an A/D card in the PC or a PLC. The feedback signal can, 
alternatively, be monitored through the USB connection between 
the ER5000 and the PC by reading variable #44 (ID_FEEDBACK).

TRANSDUCER

YELLOW

ORANGE

+ I IN
- I IN

BLACK

VIOLET

PC

+ SUPPLY

+ OUTPUT

Figure 35: Monitor 4–20 mA External Feedback (Ground Referenced Input) 

 WARNING

The controller must be disconnected from the power supply before 
any additional wiring or change to jumper configuration is 
performed. Do not reconnect the power supply until all additional 
wiring connections have been made and are properly installed.

Refer to Table 18 to verify correct wiring.

Table 18: Wiring for Monitoring 4–20 mA External Feedback (Ground Referenced Input) 

J3 Pins

Wire Color

Function

1

brown

+setpoint input

2

red

-setpoint input

3

orange

+feedback input

4

yellow

-feedback input

5

green

-RS485 network connection

6

blue

+RS485 network connection

7

violet

+24V DC power

8

gray

24V return (power ground)

9

white

+5V output (5 mA max.)

10

black

analog signal/board ground

*

11

*

pink

analog signal output

(active in Enhanced “F” models ONLY)

12

tan

analog signal/board ground

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

The wiring shown in Figure 35 is for a two wire 

transducer. Refer to 

Figure 32

 and 

Figure 33

, respectively, for 

correct wiring of three wire and four wire transducers.

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

Check that 

Jumper J6

 (refer to 

Figure 19

) is installed for 

4–20 mA operation. 

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов