Emerson Tescom ER5000 Series Скачать руководство пользователя страница 167

Страница: 167 / 248

ER5000

—

167

The ERTune™ Program: Basic Features

Additional Commands Available for “F” Model ER5000s

Soak

Pauses the Profile while the ER5000 responds to a step setpoint
change, then dwells at that setpoint for a specified amount of
time. The

Error Band (psig)

field sets the range (+/-) around the

setpoint. When feedback falls within this range, the ER5000
maintains the new setpoint for the amount of time, in seconds,
entered in the

Time to Soak (sec)

entry field.

NOTE

CAUTION

WARNING

The Dwell command counts off the specified time regardless of

ER5000 response. The Soak command accounts for rise and settling time
before counting off the specified time.

Allows the Profile to respond to the current state of the system.
Checks whether a parameter of the current system status matches
the condition specified in the

Condition, Operator and Value

fields.

•

If the condition is TRUE, the next command in the Profile
is executed.

•

If the condition is FALSE, the next command is skipped.

NOTE

CAUTION

WARNING

To execute a multi-line command sequence based on the same

condition, use the If command together with the

Goto

command, which

is described on the next page.

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 167 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: