Emerson Tescom ER5000 Series Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 248

Emerson Tescom ER5000 Series Скачать руководство пользователя страница 163

ER5000

—

163

The ERTune™ Program: Basic Features

The Profile Builder Panel

The middle panel of the Profile Tab holds the tools for adding,
modifying and deleting segments of the Profile.

Figure 61: Drop-down Command Lists for “S” Model and “F” Model ER5000s

The Segment Types Window

The Segment Types Window displays the editing fields for a
command when it is selected from the drop-down list or by
clicking one of the three buttons. The

Ramp

,

Dwell

and

Step

buttons allow you to quickly select the three most commonly
used commands.

The Segment Editor Window

There are three buttons in this window.

Insert

This button adds a new segment to the Profile. The new segment
is added above the segment that is currently selected in the
Profile Window.

Modify

This button saves the edits made to an existing segment.

IMPORTANT!

IMPORTANT!

You must click this button to update the Profile.

Delete

This button deletes the currently selected segment in the
Profile Window.

«
...
161
162
163
164
165
...
»

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов