Emerson Tescom ER5000 Series Скачать руководство пользователя страница 71

Страница: 71 / 248

ER5000

—

Getting Started

Connect the USB cable

(not supplied with ER5050)

WARNING

The controller must be disconnected from the power

supply before any additional wiring or change to jumper

configuration is performed. Do not reconnect the power

supply until all additional wiring connections have been

made and are properly installed.

WARNING

Refer to

Installing a Hazardous Location

Model (ER5050)

page 110

for more information on wiring in

a Hazardous Location application. Refer to

page 89

through

page 93

for correct wiring variations using RS485.

The cable included with the ER5000 has a standard USB A
connector on one end and a 90° Mini-B connector on the other.
1. Slide the Mini-B connector into the left conduit port in the

base of the ER5000 as shown in Figure 13.

2. Thread the cable over the control board and plug it into

the Mini-B USB port.

3. Remove any excess slack in the cable and secure the

integrated strain relief into the conduit port.

4. Plug the cable’s USB A connector into the computer that

will run the ERTune™ program.

5. Screw the cover back onto the ER5000 until you have a

tight fit and plug in the power supply.

Integrated USB

Strain Relief

90° Mini-B Connector

Mini-B Port

Figure 13: Connect the USB Cable

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 71 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: