Emerson Tescom ER5000 Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 248

Emerson Tescom ER5000 Series Скачать руководство пользователя страница 117

ER5000

—

117

The ERTune™ Program: Basic Features

Where to Find the ERTune™ Program Files on Your PC

The ERTune™ program creates two folders on your C: drive
during installation.

On PCs running Windows 7, the program files, including the
program executables, device drivers, support files and reference
materials, are located at:

C: -> Program Files (x86) -> Emerson -> ERTune

.

On PCs running previous versions of Windows, this is located at:

C: -> Program Files -> Emerson -> ERTune

.

A separate folder is created for data files generated by the
program. On PCs running Windows 7, this is located at:

C: -> Program Data -> Emerson -> ERTune

.

On PCs running previous versions of Windows, this is located at:

C: -> Documents and Settings -> All Users -> Application Data -> Emerson -> ERTune

.

This folder is the default location for configuration files, Profiles
and data acquisition files. The Windows Navigator window will
default to this folder. You may save the data files generated by
your application in another location, if you prefer.

«
...
115
116
117
118
119
...
»

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов