manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 194 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 194

 

ER5000

 — 

194

The ERTune™ Program: Power User

Deadband

This is the Pulse Width Deadband, the “deadband within a 
deadband” of the Integral Deadband. When feedback falls within 
this inner range, Pulse Mode stops responding.
Pulse Width Deadband is set to a much smaller level than Integral 
Deadband, allowing the ER5000 to respond to a very small level 
or error.

• 

Integral Deadband is generally set within a range of 0–0.5% 
of feedback. 

• 

Pulse Width Deadband is set by counts of error. Each count 
equates to .03% of feedback. Pulse deadband is generally set 
at 1–3 counts, which equates to .03–.09% of feedback.

To change the Pulse Width settings

1.  Enter a new value in the 

Period

, 

Width

 or 

Deadband

 field and 

press the Tab key.

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

The values should be changed incrementally until the 

desired response is achieved.

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов