Emerson Tescom ER5000 Series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 248

Emerson Tescom ER5000 Series Скачать руководство пользователя страница 75

ER5000

—

75

Getting Started

11

Start up and tune the system

WARNING

•

Start up sequence for electropneumatic controllers is:
a. Feedback loop must be installed and operational.
b. Electrical power should be applied and system setpoint reduced to

its lowest pressure output before turning on the pneumatic supply to

the controller.

c. Apply pressure to the system gradually, avoiding a sudden surge of

fluid or pressure shock to the equipment in the system.

•

To avoid personal injury and property damage, keep hands, tools and

other objects away when applying power to the controller.

•

Changes to the instrument setup may cause changes in the output

pressure. Depending on the application, these changes may upset process

control, which may result in personal injury or property damage.

•

Most controls in the ERTune

™

program operate in real time and have

an immediate effect on system performance. Be aware of system

limitations before you change the settings of a control. Depending on

the application, these changes may upset the process control, which

may result in personal injury or property damage.

The ER5000 is now fully installed. Connect the regulator supply
pressure to the Inlet Port of the regulator.
The system performance can be checked and, if desired, optimized
further using the ERTune™ program.

Refer to

The ERTune™ Program: Basic Features

section for further details

and recommendations on tuning the pressure control system.

ER5000 Supply

Pressure

110 psig / 7.5 bar

Transducer

USB Connection

Power

Supply

+24V DC

VIOLET

YELLOW

ORANGE

+ SUPPLY

+ S

U

PPL

Y

+ O

U

TP

U

T

GRAY

TAN

PC

Supply Pressure

To Process

Regulator

GROUND

Adaptor

Figure 17: The Completed ER5000 Installation

«
...
73
74
75
76
77
...
»

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов