manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 235 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 235

 

ER5000

 — 

235

Internal Variables

ER5000 Control Limit Variables 

64   ID_PWM_CONTROL_LIMIT

This variable sets the condition of the controller if any of the 
programmed limits are exceeded. Normally, the unit will be 
set up to open the exhaust and close the inlet valve if a limit 
is exceeded. 

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

When shipped from the factory the limits are set to 

their outer boundaries (disabled). The unit will automatically 
remove itself from the control limit condition when the limit 
is no longer exceeded. 

• 

0 => IN_CLOSED_EX_CLOSED

• 

1 => IN_OPEN_EX_CLOSED

• 

2 => IN_CLOSED_EX_OPEN

• 

3 => IN_OPEN_EX_OPEN 

Control Limits for Specified Signals 

These variables are the minimum and maximum values allowed 
for a given signal that is permissible before tripping a limit and 
causing the unit to go into the specified Control Limit Condition. 

Table 28: Control Limits for Specified Signals

Minimum/Maximum

Limited Signal

54 – ID_MIN_AD_SETPOINT
55 – ID_MAX_AD_SETPOINT

1 – ID_AD_SETPOINT

56 – ID_MIN_COMPENSATED_INTERNAL_SENSOR
57 – ID_MAX_COMPENSATED_INTERNAL_SENSOR

6 – ID_COMPENSATED_INTERNAL_SENSOR

58 – ID_MIN_COMPENSATED_EXTERNAL_SENSOR
59 – ID_MAX_COMPENSATED_EXTERNAL_SENSOR

7 – ID_COMPENSATED_EXTERNAL_SENSOR

60 – ID_MIN_INNER_ACTUAL_ERROR
61 – ID_MAX_INNER_ACTUAL_ERROR

0 – ID_INNER_ACTUAL_ERROR

62 – ID_MIN_OUTER_ACTUAL_ERROR
63 – ID_MAX_OUTER_ACTUAL_ERROR

14 – ID_OUTER_ACTUAL_ERROR

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов