manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 225 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 225

 

ER5000

 — 

225

Internal Variables

ER5000 Internal Variables 

The ER5000 has a number of internal variables which can be 
accessed via the USB or RS485 interface. The most commonly 
used variables are listed below. The variable index number, 
name and description are shown. The index number is the value 
selected from the drop-down list in the 

Variables

 field of 

The Read/

Write Panel

 in 

The Power User Tab

 of the ERTune™ program to 

access the specified variable. A complete list of internal variables 
is shown in 

Table 27

. 

ER5000 Setpoint and Feedback Variables 

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

For variable #37 (ID_SETPOINT) and variable #44 (ID_FEEDBACK), 

a value of 400 counts is 0% and 3700 counts is 100%. To convert between 
counts and percent, use the following formulas: 

• 

value_percent = (value_counts - 400) * 100 / 3,300

• 

value_counts = ( value_percent * 3,300 /100) + 400

37 ID_SETPOINT

This is the controller’s setpoint. 

43 ID_SETPOINT_FLAG

This variable determines the source of the setpoint, 
variable #37 (ID_SETPOINT).

• 

0 =>  setpoint from A/D, analog setpoint input

• 

1 =>  setpoint from RS485 or USB network, typically a PC

• 

2 =>  setpoint from internal Profile

• 

3=>   setpoint from A/D, analog setpoint input, while in 

Profile Mode

• 

4=>   Monitor Setpoint from external device while running 

the ERTune™ program

44 ID_FEEDBACK

This is the controller’s overall feedback signal. For internal sensor 
mode it is the same as inner feedback. For external sensor 
mode or cascade mode it equals the outer loop feedback. 

87   ID_EXT_FEEDBACK_SOURCE

This variable determines the source of the external feedback.

• 

0 =>   feedback from the compensated external sensor, see 

variable #5 (ID_COMPENSATED_EXTERNAL_SENSOR)

• 

1 =>  feedback from extra analog input 1, see variable #77 

(ID_COMPENSATED_EXTRA_AD1) 

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов