Emerson Tescom ER5000 Series Скачать руководство пользователя страница 154

Страница: 154 / 248

ER5000

—

154

The ERTune™ Program: Basic Features

6. Step back the Proportional slider to minimize

unwanted effects.

Figure 53: Typical Tuning: Proportional Optimized

Overall, the response is quick and stable. Derivative will be used to correct the

small amount of residual overshoot.

To add the Derivative Term

1. Move the Derivative slider slightly to the right or enter a

higher number in the field next to the slider.

2. Toggle the setpoint and note the change to the

response curve.

Figure 54: Typical Tuning: Derivative Added

A higher Derivative setting will completely correct the overshoot.

(continued next page)

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 154 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: