Emerson Tescom ER5000 Series Скачать руководство пользователя страница 70

Страница: 70 / 248

ER5000

—

Getting Started

Connect the transducer wiring to provide a
feedback signal (cont.)

2. Connect the orange feedback input wire (Pin 3) to the

signal output of the transducer, which is Pin 2 or B on
TESCOM™ transducers.

3. Connect the positive wire from the 24V DC power supply

to the power input of the transducer, which is Pin 1 or A on
TESCOM transducers.

4. Connect the yellow feedback return wire (Pin 4) to the tan

analog ground wire (Pin 12).

NOTE

CAUTION

WARNING

This is necessary to complete the ground circuit for the

signal from the transducer.

For other applications and wiring configurations, refer to the

Installation Variations

section.

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 70 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: