Emerson Tescom ER5000 Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 248

Emerson Tescom ER5000 Series Скачать руководство пользователя страница 118

ER5000

—

118

The ERTune™ Program: Basic Features

Installing the ERTune™ Program

The ERTune™ program provides an intuitive interface to
customize the performance of the ER5000 to meet the specific
requirements of your application. Using the controls and features
of the program, you can:

•

Manually tune the PID parameters to optimize the response of
the ER5000.

•

Create and download Profiles that guide the ER5000 through
multi-segment sequences of commands.

•

Track, save and review data acquired during tuning sessions
and normal system operation.

•

Configure basic operating parameters and set up the ER5000
to monitor and respond to system Control Limits.

•

Perform basic troubleshooting.

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

The ERTune™ program is available in English, German and

Chinese versions. When installation begins, the installer checks the
default language settings for the computer and if German or Chinese are
detected, the corresponding translated version is installed. Otherwise,
the English version is installed.

To install the ERTune™ program

1. Download the ER5000 Software and Manual file which can be

found at TESCOM.com under the “Download ER5000 Software
and Manual” link. Once the file is downloaded, extract the zip
file, click on the .exe file, and the ER5000 User Support Software
and Manual menu will open.

2. The ER5000 User Support Software and Manual menu gives you

access to the programs and reference materials. Click the

Install

ERTune

button.

3. Follow the steps in the ERTune Setup Wizard. When Installation

is complete, click

Close

.

«
...
116
117
118
119
120
...
»

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов