manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 211 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 211

 

ER5000

 — 

211

Troubleshooting

Operation

Checking the ERTune™ Menu Bar for Warnings

The Menu Bar of ERTune™ program displays two 
warnings: 

No Feedback

 and 

Simulation

. 

The 

No Feedback

 warning indicates that the program is 

communicating with the controller, but is not receiving a 
feedback signal. 

This warning generally indicates a wiring problem. Refer 
to the 

Getting Started 

or the

 Installation Variations 

section to find the correct wiring for your application and 
verify that your wiring has been installed correctly. 

• 

A common error is not connecting the yellow wire 
(pin 4) and the tan wire (pin 12) when using a 
4–20 mA feedback transducer.

• 

Also check to make sure the voltage/current 
select jumpers are in the proper position for your 
application. Refer to 

Checking the Configuration of 

the Jumpers

 earlier in this section.

The 

Simulation

 warning indicates that the ERTune™ 

program has been opened in Simulation Mode. 

In Simulation Mode, the program responds 
normally to controls. However, it does not actively 
communicate with a controller, even if the controller 
is powered up and properly connected.

Simulation Mode is useful for training purposes, but 
should be closed when you wish to communicate 
with the ER5000.

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов