Emerson Tescom ER5000 Series Скачать руководство пользователя страница 121

Страница: 121 / 248

ER5000

—

121

The ERTune™ Program: Basic Features

3. In the

ER Model

drop-down list, select the ER model number

that matches the model number of your controller.

NOTE

CAUTION

WARNING

All ER5000 model numbers have a “-1” extension. This

extension has been truncated from the model numbers displayed
in the list.

4. Click the

Next >

button. The Control Mode window opens.

5. The Setup Wizard reads and displays the current Control

Mode for your controller.

External Feedback

is default for new

controllers. The other options are

Internal Feedback

and

Cascade.

6. Select the Control Mode that is appropriate for your

application and click the

Next >

button. The Sensor Range

window opens.

The fields in this window set the default range and the unit of
measurement for the Plot Screen in the ERTune™ program.
The default is percentage; you can change this to psig or bar
or some other unit of measurement.

CAUTION

If you change the unit of measurement from percentage,
be sure your

Min

and

Max

values accurately represent the

specifications for your feedback source.

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 121 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: