Emerson Tescom ER5000 Series Скачать руководство пользователя страница 169

Страница: 169 / 248

ER5000

—

169

The ERTune™ Program: Basic Features

Digital Output (ER Outputs are Ports 3 & 4)

Sends a signal to trigger a process in another part of the system.
Refer to the

Digital Outputs

wiring configuration for an example

of an ER5000 with digital outputs.

Enter the ER5000 port number for the digital output in the

Port

Number

field and the ER5000 port state (0 => open circuit, 1=>

closed circuit) in the

Port State

entry field.

Digital Input (ER Input is Port 3)

Pauses the Profile until the specified input is set to the specified
state. Refer to the

Profile with External Control/Digital Inputs

wiring configuration for an example of an ER5000 with
digital inputs.

Enter the ER5000 port number for the digital input in the

Port

Number

field and the ER5000 port state (0 => open circuit, 1=>

closed circuit) in the

Port State

entry field.

Содержание Tescom ER5000 Series

























































































































































































































































Результаты поиска

Содержание Tescom ER5000 Series

Отзывы:

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 169 / 248

Результаты поиска

Содержание Tescom ER5000 Series

Отзывы: