manualshive.com logo in svg

Emerson Tescom ER5000 Series, Руководство пользователя, Страница: 52 / 248

Поделиться
Скачать
Emerson Tescom ER5000 Series Скачать руководство пользователя страница 52

ER5000

 — 

52

Glossary of Terms

Terms Relating to Regulators

Accuracy

The acceptable level of pressure variation for a 

Regulator

 under 

steady state conditions within its control range. All physical and 
mechanical processes have some level of variation.

Air Actuated

Also known as Air Loaded: one type of loading element for a 
pressure 

Regulator

. Utilizes low pressure gas as the 

Loading 

Element (Loading Force)

, typically 0–80 psig / 0–5.5 bar. This 

is a form of ratio loading: the regulator uses low 

Pilot Pressure

 

to regulate a 

Control Pressure

 that may be much higher (see 

Ratio Actuator)

. The most common type of regulator used with 

the ER5000, as it is the only type that can be used for control 
pressures greater than 100 psig / 6.9 bar. 

Captured Venting

Feature incorporated in some venting 

Regulators

 which provides 

an additional port that can be connected to piping in order to safely 

dispose of excess liquid or gas expelled by the regulator’s vent valve. 
The vent port should never be plugged. Not all venting regulators 
have this feature. Refer to 

Venting Regulator

.

Control Element

One of the three basic elements of a 

Regulator

. Acts to reduce high 

Inlet Pressure

 to a lower working pressure (

Outlet Pressure)

. The 

control element is sometimes called the main valve, valve stem 
or poppet.

Control Pressure

The component of 

System Pressure

 that is the result of the 

regulating action of the 

Regulator

. Can be either the 

Outlet Pressure

 

or the 

Inlet Pressure

, depending on the type of regulator. For a 

pressure reducing regulator, the control pressure is the Outlet 
pressure. For a back pressure regulator, the control pressure is the 
Inlet pressure.

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов